Make a Selection
|
|
3M™ Accessories - Grounding Cord, 3040
Ground Cord, 15 ft. (4.6 m), with 10 mm snap. Molded-in male snap fastener with integral 1 megohm resistor on one end, solderless terminal on other. Connects all 3M™ Static Control Mats and Runners to building ground.
|
|
3M™ Accessories - Grounding Kit, 3041
Grounding Kit for 3M™ Static Protective Hard Laminate includes #10 screw, lock washer, #10 nut, lock washer wing nut, #10 self-tapping screw and one 10 ft. (3.0 m) ground cord. Ground cord has a 1 megohm resistor.
|
|
3M™ Accessories - Grounding System, 3042
Wrist Strap Grounding System. Grounds two single conductor wrist straps and conveniently mounts beneath the edge of most work benches. Comes complete with 10 ft. (3.0 m) ground cord.
|
|
3M™ Accessories - Insulated Bulldog Clip, 3037
Fits Standard Banana Plug
|
|
3M™ Accessories - Interconnect Cord, 3043
Interconnect Cord 5 ft. (3.5 m), with 10 mm snap. Molded-in male snap fastener at each end. Connects all static control mats and runners to each other. Ground cord has a 1 megohm resistor.
|
|
|
3M™ Accessories - Snap Fastener, 3033
Snap Fastener, male, 0.125 in. (3.2 mm) hole, 10 mm diameter. For mats and runners. 1800/8800 Series.
|
|
3M™ Accessories - Snap Fastener, 3034
Snap Fastener, female, 0.125 in. (3.2 mm) hole, 10 mm diameter. For 3M™ Mats and Runners 1800/8800 series.
|
|
3M™ Accessories - Uninsulated Bulldog Clip, 3038
Fits standard banana plug.
|
|
3M™ Dual Conductor Remote Input Jack, 732
The 3M Remote Input Jack 732 May Be Purchased As A Replacement Part For The 3M™ Workstation Monitor 724. It Provides Two Phone Jacks - One For The Primary Worker And One For Use By Visitors To The Work Area.
|
|
3M™ Dual Conductor Remote Input Jack, 733
733 Remote Splitter Kit offers the versatility of grounding and monitoring two workers at independent workstations that are in close proximity. The unit features a quick/disconnect system. To Be Used With Workstation Monitor 724
|
|
3M™ Ground Cord with Center Snap for Standard Field Service Kits 3051
Ground Cord with center snap for standard field service kits. Wrist strap cord section 10 ft. (3.0 m) and ground cord section 5 ft. (1.5 m). Each contains a 1 megohm resistor.
|
|
3M™ Monitor/Table Mat Replacement Cord
Monitor/Table Mat Replacement Cord, 6 ft. (1.8 m), with 10 mm snap. Extends from the 3M™ Wrist Strap Workstation Monitor 724 to the static control worksurface to be monitored. This cord does not have a resistor molded into the snap fastener cap.
|
|
3M™ Table Mat Interconnect Cord, 2389
Monitor/Table Mat Interconnect Cord, 10 ft. (3 m), with 10 mm snap. A straight cord with male snap fasteners at each end and no resistors. Used to interconnect two monitored worksurfaces.
|
|
3M™ Workstation Product - Common Point Grounding System, 3047
Common Point Grounding System, 10 ft. (3 m) to ground workstation components. Single-row, six-terminal strip, protective cover, three cable clips. Ground cord has a 1 megohm resistor.
|
|
3M™ Workstation Product - Grounding System, 3048
Easily snaps onto mats and runners, (10 mm snap); grounds two single conductor wrist straps. Comes complete with ring connector and 15 ft. (4.6 m) ground cord. Ground cord has a 1 megohm resistor for mat connection only.
|
|
3M™ Workstation Product - Snap Fastener, 3050
Snap Fastener, female, 10 mm diameter. For 3M™ Table and Floor Mats and Runners 8200 Series.
|
|
3M™ Workstation Product - Stand-By Jack, 3057
Monitor Stand-By Jack. Allows Operator To Disconnect A Ground Cord From The Wrist Band And Leave The Workstation Without Deactivating The 3M™ Wrist Strap Workstation Monitor 724 Or 3M™ Static Monitor 790.
|
Printer-friendly format
